Similarities and differences between impact crusher and hammer crusher



Similarities and differences between impact crusher and hammer crusher

1. The crushing ratio of the impact crusher is large, and the shape of the finished material is good;But hammer crusher crushing ratio is small, the product has more needle piece shape , the powder content is high, the crushing efficiency is low, output is low.

2. The spare parts of the impact crusher are easy to replace and the maintenance cost is reduced accordingly;There are more than 100 hammer heads in the hammer crusher. It takes a lot of time and manpower to replace one set of hammer heads,The maintenance and repair cost is relatively high.

3. The wear of wearing parts of the impact crusher is smaller than that of the hammer crusher, and the metal utilization rate is higher.

4. The impact crusher can conveniently and flexibly adjust the discharge particle size, and the discharge particle size has a wide range of adjustment;The hammer crusher can only be adjusted by replacing the bottom sieve plate.

5. Impact crusher is suitable for both soft and very hard materials.

6. The impact crusher can effectively deal with the materials with large moisture content and prevent the clogging phenomenon of the crusher;Hammer crushers are equipped with bottom sieve plates, increasing the possibility of clogging.

To sum up, the material size of the finished product molding requirements, humidity, and large output must choose the impact crusher, the general small stone factory, soft rock processing and the required output is low (less than 30 tons per hour), and there is no requirement for the shape of the finished product can be used hammer crusher.

If you want to know more about our equipments details,please contact us
www.shuosencrusher.com
sarahzzdshj@gmail.com

评论

发表评论

此博客中的热门博文

Operation of Jaw Crusher

图片
Operation Instructions of Jaw Crusher 1.The preparation before starting: (1) Inspect each bearing to ensure whether it lubricates well, and whether there is enough lubricating grease on the toggle plate joints and bearing inners. (2) Check carefully whether all fasteners are totally fastened. (3) Check whether the drive belt is under good condition, and change the belt if any damages can be found. When there is grease contamination on the belt or bell wheel, it can be clean up with a clean dishcloth. (4) Check whether the protective device is under good condition, if there are any unusual events and safety hazards conditions, should correct them and report. (5) Check whether there are any ore or other impurities inside the crushing cavity. 2.The starting of the crusher (1) After inspecting the machine and transmission parts are under good condition, the machine may starts. (2) This machine can only start under empty load conditions. (3) After having started the machine, shut down the
阅读全文

22 checking items in cone crusher operation

图片
22 checking items in cone crusher operation 1, must continue the cone crusher to uniform center feeding, crowded feeding can improve work efficiency.(per shift) 2. Check whether there are copper and iron chips on the oil return filter screen.(per shift) 3. Check the oil level of lubricating oil.(per shift) 4. Check and record the pressure of lubrication system and hydraulic system, and check whether the filter element is blocked.(per shift) 5, check the wear condition of the lining.(per shift) 6. Check the status of all bolts and their fasteners.(per shift) 7, check the lubricating oil pollution.(per shift) 8. Check whether the discharge area is unobstructed and remove the accumulated materials and sundries on the rack.(per shift) 9. Grease the adjusting ring when it is not locked.(per week) 10. Check and tighten the triangle belt.(per week) 11. Check and deal with all pipelines to avoid oil leakage.(per week) 12. Check and tighten the distributor plate bolts.(per week) 13, check
阅读全文

What factors affect the output of cone crusher

图片
What factors affect the output of cone crusher There are three main factors influencing the productivity of cone crusher : the number of times of the swing of the cone;The length of the parallel crushing area;The size of the engagement Angle.These three aspects directly determine the output of cone crusher. 1.the number of times of the swing of the cone The swing times of the crushed cone is one of the key factors affecting the crusher productivity. Because of the limitation of the meshing Angle of the crushing cavity and the parallel ore discharge area, the crushed ore is discharged along the taper inclined plane mainly by gravity and vibration.When the number of spindle rotation increases, the ore is easy to be discharged, but the number of rotation is too high, which is not conducive to ore discharge, sometimes resulting in faster speed and unable to produce.Therefore, the number of swing of the broken wall has a certain constraint on the improvement of productivity. 2.The l
阅读全文