the working malfunctions solving ways of Impact crusher


the working malfunctions solving ways of Impact crusher

possible malfunctions
reason for the malfunctions
solving ways
sudden increase in the vibration
the rotor does not reach a good balance when replace or install hammer plate
reinstall the hammer plate, rectify and balance the rotor
too large granularity
too much abrasion in the lining plate and hammer plate lead to a too large clearance
through adjusting the distance between forward and backward impact shelf or replace the lining plate or hammer plate
tattoo noise in the machine
1.the material which can not be crushed get into the machine
2.the fasteners on the lining plate are loosened, hammer hits the bracket
3.hammer or other components breaks
1.
clean up the crushing chamber after it stops
2.examine the tightness of the lining plate and the space between the hammer and lining plate
3.replace the broken parts
too high temperature with the bearing
1.too much or little lubrication
2.grease is dirty
3.the bearing is damaged
1.check the grease amount is appropriate or not
2.change the grease after cleaning the bearing
3.replace the bearing

If you want to know more about our equipments details,please contact us
www.shuosencrusher.com
sarahzzdshj@gmail.com

评论

发表评论

此博客中的热门博文

Operation of Jaw Crusher

图片
Operation Instructions of Jaw Crusher 1.The preparation before starting: (1) Inspect each bearing to ensure whether it lubricates well, and whether there is enough lubricating grease on the toggle plate joints and bearing inners. (2) Check carefully whether all fasteners are totally fastened. (3) Check whether the drive belt is under good condition, and change the belt if any damages can be found. When there is grease contamination on the belt or bell wheel, it can be clean up with a clean dishcloth. (4) Check whether the protective device is under good condition, if there are any unusual events and safety hazards conditions, should correct them and report. (5) Check whether there are any ore or other impurities inside the crushing cavity. 2.The starting of the crusher (1) After inspecting the machine and transmission parts are under good condition, the machine may starts. (2) This machine can only start under empty load conditions. (3) After having started the machine, shut down the
阅读全文

22 checking items in cone crusher operation

图片
22 checking items in cone crusher operation 1, must continue the cone crusher to uniform center feeding, crowded feeding can improve work efficiency.(per shift) 2. Check whether there are copper and iron chips on the oil return filter screen.(per shift) 3. Check the oil level of lubricating oil.(per shift) 4. Check and record the pressure of lubrication system and hydraulic system, and check whether the filter element is blocked.(per shift) 5, check the wear condition of the lining.(per shift) 6. Check the status of all bolts and their fasteners.(per shift) 7, check the lubricating oil pollution.(per shift) 8. Check whether the discharge area is unobstructed and remove the accumulated materials and sundries on the rack.(per shift) 9. Grease the adjusting ring when it is not locked.(per week) 10. Check and tighten the triangle belt.(per week) 11. Check and deal with all pipelines to avoid oil leakage.(per week) 12. Check and tighten the distributor plate bolts.(per week) 13, check
阅读全文

What factors affect the output of cone crusher

图片
What factors affect the output of cone crusher There are three main factors influencing the productivity of cone crusher : the number of times of the swing of the cone;The length of the parallel crushing area;The size of the engagement Angle.These three aspects directly determine the output of cone crusher. 1.the number of times of the swing of the cone The swing times of the crushed cone is one of the key factors affecting the crusher productivity. Because of the limitation of the meshing Angle of the crushing cavity and the parallel ore discharge area, the crushed ore is discharged along the taper inclined plane mainly by gravity and vibration.When the number of spindle rotation increases, the ore is easy to be discharged, but the number of rotation is too high, which is not conducive to ore discharge, sometimes resulting in faster speed and unable to produce.Therefore, the number of swing of the broken wall has a certain constraint on the improvement of productivity. 2.The l
阅读全文