About The Dry magnetic separator

About The Dry magnetic separator

Dry magnetic separator is very suitable for arid areas, saving water resources, reducing the cost of mineral processing, for the ultra-lean magnetite mining and utilization of a new way.

Magnetic separation is a method to separate useful minerals from minerals according to their magnetism.

Magnetic separation is one of the most widely used and mature technologies, which is mainly used for the separation of magnetic minerals. Magnetic separation machine plays an important role in this process.The mined ore is first broken by a jaw crusher, which is broken to a reasonable fineness and then uniformly sent to a ball mill by a hoist and a ore feeder, which crushes and grinds the ore.After the ball mill grinding ore fine material into the next process: grading.The spiral classifier cleans and classifies the ore mixture by the principle that the proportion of solid particles is different and the rate of precipitation in the liquid is different.When the cleaned and graded mineral mixture passes through the magnetic separator, the magnetic substances in the mixture are separated by magnetic force and mechanical force due to the different specific magnetization coefficients of various minerals.Note: this process is designed according to the standard process and can be optimized according to the annual output and requirements of customers.


Dry magnetic separators are used in the following five occasions.
Occasion 1: dry magnetic separator can be used for preconcentration of low-grade ores, preconcentration of ore resources, improvement of grinding grade and reduction of dressing cost.
Occasion two: dry magnetic separator used for tailings reprocessing, recovery tailings dam relatively concentrated tailings.
Occasion 3: dry magnetic separator is used for the magnetic separation and purification of sulfuric acid slag powder.
Occasion 4: dry magnetic separator is used for removing iron from non-magnetic materials.
Occasion 5: dry magnetic separator is used for purifying iron fine powder in magnetic separation plant.

If you want to know more about our equipments details,please contact us
Shanghai Shuosen Mining Machine Co.,Ltd
www.shuosencrusher.com
sarahzzdshj@gmail.com
sarah@shuosencrusher.com

评论

发表评论

此博客中的热门博文

Operation of Jaw Crusher

图片
Operation Instructions of Jaw Crusher 1.The preparation before starting: (1) Inspect each bearing to ensure whether it lubricates well, and whether there is enough lubricating grease on the toggle plate joints and bearing inners. (2) Check carefully whether all fasteners are totally fastened. (3) Check whether the drive belt is under good condition, and change the belt if any damages can be found. When there is grease contamination on the belt or bell wheel, it can be clean up with a clean dishcloth. (4) Check whether the protective device is under good condition, if there are any unusual events and safety hazards conditions, should correct them and report. (5) Check whether there are any ore or other impurities inside the crushing cavity. 2.The starting of the crusher (1) After inspecting the machine and transmission parts are under good condition, the machine may starts. (2) This machine can only start under empty load conditions. (3) After having started the machine, shut down the
阅读全文

22 checking items in cone crusher operation

图片
22 checking items in cone crusher operation 1, must continue the cone crusher to uniform center feeding, crowded feeding can improve work efficiency.(per shift) 2. Check whether there are copper and iron chips on the oil return filter screen.(per shift) 3. Check the oil level of lubricating oil.(per shift) 4. Check and record the pressure of lubrication system and hydraulic system, and check whether the filter element is blocked.(per shift) 5, check the wear condition of the lining.(per shift) 6. Check the status of all bolts and their fasteners.(per shift) 7, check the lubricating oil pollution.(per shift) 8. Check whether the discharge area is unobstructed and remove the accumulated materials and sundries on the rack.(per shift) 9. Grease the adjusting ring when it is not locked.(per week) 10. Check and tighten the triangle belt.(per week) 11. Check and deal with all pipelines to avoid oil leakage.(per week) 12. Check and tighten the distributor plate bolts.(per week) 13, check
阅读全文

What factors affect the output of cone crusher

图片
What factors affect the output of cone crusher There are three main factors influencing the productivity of cone crusher : the number of times of the swing of the cone;The length of the parallel crushing area;The size of the engagement Angle.These three aspects directly determine the output of cone crusher. 1.the number of times of the swing of the cone The swing times of the crushed cone is one of the key factors affecting the crusher productivity. Because of the limitation of the meshing Angle of the crushing cavity and the parallel ore discharge area, the crushed ore is discharged along the taper inclined plane mainly by gravity and vibration.When the number of spindle rotation increases, the ore is easy to be discharged, but the number of rotation is too high, which is not conducive to ore discharge, sometimes resulting in faster speed and unable to produce.Therefore, the number of swing of the broken wall has a certain constraint on the improvement of productivity. 2.The l
阅读全文