If the Jaw crusher discharge particle size is not up to standard, how can we adjust the jaw crusher?

If the Jaw crusher discharge particle size is not up to standard, how can we adjust the jaw crusher?


Jaw crusher discharge particle size is not up to standard, can adjust the jaw crusher outlet.There are three ways to adjust the outlet of the jaw crusher. 1.gasket adjustment: open the adjusting seat with the lifting bolt, check the quality of the rear thrust plate support and the rear wall of the rack, and put or remove a group of gaskets with equal thickness.By increasing or decreasing the number of gasket layers, the discharge port of the crusher decreases or increases.2. hydraulic adjustment: the rear thrust plate is used as the safety device of the crusher.The crusher adopts hydraulic safety device, which is reliable, safe and easy to discharge faults.3. support device adjustment: refers to the bearing part of the jaw crusher, generally using cast-babbitt alloy sliding bearing, it can withstand a greater impact load, and more wear resistance, but to low efficiency, the need for forced lubrication.The jaw crusher also divides the size, divides into the large-scale jaw crusher and the miniature jaw crusher.Two kinds of jaw crusher adjustment mode is different, large jaw crusher hydraulic adjustment mode, non - human adjustment.Small jaw crusher is relatively small, generally using gasket adjustment or support device adjustment, if the force is insufficient, can use the jack.

The specific situation also depends on your actual situation, because the first crushing throughput is too large, behind digestion, will cause blockage phenomenon;If it is too small, it will cause idle running of the machine and waste of resources.In addition, the size of the material and stone hardness is also a great relationship.

If you want to know more about our equipments details,please contact us

Shanghai Shuosen Mining Machine Co.,Ltd
www.shuosencrusher.com
sarahzzdshj@gmail.com
sarah@shuosencrusher.com

评论

发表评论

此博客中的热门博文

Operation of Jaw Crusher

图片
Operation Instructions of Jaw Crusher 1.The preparation before starting: (1) Inspect each bearing to ensure whether it lubricates well, and whether there is enough lubricating grease on the toggle plate joints and bearing inners. (2) Check carefully whether all fasteners are totally fastened. (3) Check whether the drive belt is under good condition, and change the belt if any damages can be found. When there is grease contamination on the belt or bell wheel, it can be clean up with a clean dishcloth. (4) Check whether the protective device is under good condition, if there are any unusual events and safety hazards conditions, should correct them and report. (5) Check whether there are any ore or other impurities inside the crushing cavity. 2.The starting of the crusher (1) After inspecting the machine and transmission parts are under good condition, the machine may starts. (2) This machine can only start under empty load conditions. (3) After having started the machine, shut down the
阅读全文

22 checking items in cone crusher operation

图片
22 checking items in cone crusher operation 1, must continue the cone crusher to uniform center feeding, crowded feeding can improve work efficiency.(per shift) 2. Check whether there are copper and iron chips on the oil return filter screen.(per shift) 3. Check the oil level of lubricating oil.(per shift) 4. Check and record the pressure of lubrication system and hydraulic system, and check whether the filter element is blocked.(per shift) 5, check the wear condition of the lining.(per shift) 6. Check the status of all bolts and their fasteners.(per shift) 7, check the lubricating oil pollution.(per shift) 8. Check whether the discharge area is unobstructed and remove the accumulated materials and sundries on the rack.(per shift) 9. Grease the adjusting ring when it is not locked.(per week) 10. Check and tighten the triangle belt.(per week) 11. Check and deal with all pipelines to avoid oil leakage.(per week) 12. Check and tighten the distributor plate bolts.(per week) 13, check
阅读全文

What factors affect the output of cone crusher

图片
What factors affect the output of cone crusher There are three main factors influencing the productivity of cone crusher : the number of times of the swing of the cone;The length of the parallel crushing area;The size of the engagement Angle.These three aspects directly determine the output of cone crusher. 1.the number of times of the swing of the cone The swing times of the crushed cone is one of the key factors affecting the crusher productivity. Because of the limitation of the meshing Angle of the crushing cavity and the parallel ore discharge area, the crushed ore is discharged along the taper inclined plane mainly by gravity and vibration.When the number of spindle rotation increases, the ore is easy to be discharged, but the number of rotation is too high, which is not conducive to ore discharge, sometimes resulting in faster speed and unable to produce.Therefore, the number of swing of the broken wall has a certain constraint on the improvement of productivity. 2.The l
阅读全文